Launch offer: $20 off your order with code

NSE7_FSN_AR-7.6 Practice questions

Fortinet NSE 7 - Secure Networking 7.6 Architect

0/10 checked

free questions
10
with answers
in the full set
177
question types
2

Updated

  1. Question 1

    Single answer

    Consider the scenario where the server name indication (SNI) does not match either the common name (CN) or any of the subject alternative names (SAN) in the server certificate.

    Which action will FortiGate take when using the default settings for SSL certificate inspection?

    Choose one answer
    Show answer

    Correct answer

    • D

      FortiGate uses the CN information from the Subject field in the server certificate.

    Explanation

    When FortiGate performs SSL certificate inspection with default settings, it checks if the Server Name Indication (SNI) matches either the Common Name (CN) or any Subject Alternative Name (SAN) in the server certificate. If there is no match, FortiGate does not block the connection; instead, it uses the CN value from the certificate's subject field to continue web filtering and categorization.

    This behavior is described in the official Fortinet 7.6.4 Administration Guide:

    “Check the SNI in the hello message with the CN or SAN field in the returned server certificate: Enable: If it is mismatched, use the CN in the server certificate.” This is the default (Enable) mode, which differs from the Strict mode that would block the mismatched connection.

    By default, this policy ensures service continuity and prevents disruptions due to certificate mismatches, allowing FortiGate to log and inspect based on the CN even when the requested SNI does not match. It provides a balance between connection reliability and the accuracy of filtering by certificate identity, allowing security policies to remain functional without unnecessary blocks. This approach is recommended by Fortinet to maintain usability for end-users while still supporting granular inspection.

    FortiGate 7.6.4 Administration Guide: Certificate Inspection​

    SSL/SSH Inspection Profile Configuration​

  2. Question 2

    Multiple answer

    Exhibit.

    Refer to the exhibit, which contains partial output from an IKE real-time debug. Which two statements about this debug output are correct? (Choose two.)

    Exhibit
    Choose 2 answers
    Show answer

    Correct answer

    • C

      It shows a phase 2 negotiation.

    • D

      The initiator provided remote as its IPsec peer I

    Explanation

    From the exhibit, you can observe that the debug output captures an IKEv1 negotiation in aggressive mode. Let's break down the supporting details in line with official Fortinet IPsec VPN troubleshooting resources and debug guides:

    For Option B:

    The very first line of the debug output shows:

    comes 10.0.0.2:500->10.0.0.1:500, ifindex=7.

    This indicates the traffic direction—from the remote IP (10.0.0.2) with port 500 to the local IP (10.0.0.1) with port 500. According to Fortinet's documentation, the right side of the arrow always represents the local FortiGate gateway. Thus, 10.0.0.1 is the local gateway IP address.

    For Option D:

    You see the statement:

    negotiation result "remote"

    and

    received peer identifier FQDNCE88525E7DE7F00D6C2D3C00000000

    Official debug documentation describes that the "peer identifier" or peer ID sent by the initiator is displayed here. In the context of IKE/IPsec negotiation, this value is used as the IPsec peer ID for authentication and identification purposes. The initiator is providing "remote" as the peer ID for its connection.

    Why Not A or C:

    Perfect Forward Secrecy (PFS): The debug does not show any DH group negotiation in phase 2 (no reference to group2, group5, etc., for phase 2), so you cannot deduce the presence of PFS solely from this output.

    Phase 2 negotiation: The log focuses on IKE (phase 1) negotiation and establishment; there’s no reference to ESP protocol, Quick Mode, or other identifiers that would show phase 2 SA negotiation and establishment.

    This interpretation aligns with the explanation in the FortiOS 7.6.4 Administration Guide's VPN section and the official debug command output samples published in Fortinet’s documentation. It demonstrates how to distinguish between local and remote addresses and how to identify the use of peer IDs.

    FortiOS 7.6.4 Administration Guide: IPsec VPN and Debugging VPNs

    Technical Support Resources on interpreting IKE debug output and peer ID roles

  3. Question 3

    Single answer

    Exhibit.

    Refer to the exhibit, which shows the output of a diagnose command. What can you conclude about the debug output in this scenario?

    Exhibit
    Choose one answer
    Show answer

    Correct answer

    • C

      FortiGate used 64.26.151.37 as the initial server to validate its contract.

    Explanation

    The exhibit displays the output from the diagnose debug rating command on a FortiGate device. This command is used to display information about FortiGuard Web Filtering or other security-related queries performed by FortiGate to FortiGuard servers. Official Fortinet documentation outlines the meaning of each field in the server list. The FortiGate maintains a list of available FortiGuard servers, selecting the optimal server based on factors such as weight, round-trip time (RTT), and regional settings.

    The very first entry in the server list after "Server List" is the server FortiGate initially uses, prioritized by factors such as proximity and RTT. Here, 64.26.151.37 is listed first, and the FortiGuard-requests value confirms that this server handled the highest number of requests.

    The IPs, weights, and lost/failed counters are monitored for server performance and selection over time. FortiGate's default operational logic is to try the first entry for contract validation and use the next in the list if the first is unavailable or has high latency or packet loss.

    There is no direct correlation between the Weight and the number of FortiGuard-requests. The servers with higher or lower weights may still handle different request volumes based on availability and performance.

    The TZ (time zone) value's sign (positive or negative) does not affect server preference; it is informational, showing the server's location relative to UTC, not a rating metric.

    DNS query results for FortiGuard servers are not shown here, and the provided servers are not returned in DNS query order.

    This command and interpretation are detailed in the FortiOS Administration Guide’s section describing FortiGuard server selection and contract validation processes.

    FortiOS Administration Guide: FortiGuard Service Connectivity and Debugging

    Official Technical Notes on diagnose debug rating output structure

  4. Getting the hang of it? 167 more NSE7_FSN_AR-7.6 questions to go, each with its answer. Unlock them all

  5. Question 4

    Single answer

    Refer to the exhibit, which shows the output of a policy route table entry.

    Which type of policy route does the output show?

    Exhibit
    Choose one answer
    Show answer

    Correct answer

    • D

      An SD-WAN rule

  6. Question 5

    Single answer

    Exhibit.

    Refer to the exhibit, which shows a FortiGate configuration. An administrator is troubleshooting a web filter issue on FortiGate. The administrator has configured a web filter profile and applied it to a policy; however the web filter is not inspecting any traffic that is passing through the policy. What must the administrator do to fix the issue?

    Exhibit
    Choose one answer
    Show answer

    Correct answer

    • A

      Disable webfilter-force-off.

    Explanation

    The exhibit shows a FortiGate configuration under config system fortiguard related to web filtering and FortiGuard options. There is a line:

    set webfilter-force-off enable

    According to official Fortinet documentation, the "webfilter-force-off" option, when enabled, causes the FortiGate to bypass web filtering for all traffic—even if a web filter profile is applied to a policy. This override is typically used for troubleshooting or performance reasons and is documented as an explicit bypass feature.

    If an administrator wants to enforce web filtering inspection, this setting must be disabled. The correct way to restore web filtering functionality is to run:

    set webfilter-force-off disable

    Once done, traffic passing through policies with web filter profiles will be inspected and filtered as per configuration. Other settings such as timeout or cache TTL do not bypass web filtering; they only affect operational nuances.

    FortiOS Administration Guide: Web Filtering, FortiGuard Options, “webfilter-force-off” CLI

  7. Question 6

    Multiple answer

    Exhibit 1.

    Exhibit 2.

    Exhibit

    Refer to the exhibits, which show the configuration on FortiGate and partial internet session information from a user on the internal network. An administrator would like to lest session failover between the two service provider connections. Which two changes must the administrator make to force this existing session to immediately start using the other interface? (Choose two.)

    Exhibit
    Choose 2 answers
    Show answer

    Correct answer

    • A

      Change the priority of the port1 static route to 11.

    • D

      Configure set snat-route-change enable.

    Explanation

    FortiOS Admin Guide: Static Routing, SNAT Route Change Feature

  8. Question 7

    Multiple answer

    Refer to the exhibit, which shows the output of a debug command.

    Which two statements about the output are true? (Choose two.)

    Exhibit
    Choose 2 answers
    Show answer

    Correct answer

    • A

      The interlace is part of the OSPF backbone area.

    • B

      There are a total of five OSPF routers attached to the vorz4 network segment

    Explanation

    FortiOS Admin Guide: OSPF, Debug Outputs

  9. Question 8

    Multiple answer

    Refer to the exhibit.

    Which three pieces of information does the diagnose sys top command provide? (Choose three.)

    Exhibit
    Choose 3 answers
    Show answer

    Correct answer

    • A

      The miglogd daemon is running on CPU core ID 0.

    • C

      The miglogd daemon would be on top of the list, if the administrator pressed m on the keyboard.

    • D

      The cmdbsvr process is occupying 2.4% of the total user memory space.

  10. Question 9

    Multiple answer

    Refer to the exhibit, which shows the output o! the BGP database.

    Which two statements are correct? (Choose two.)

    Exhibit
    Choose 2 answers
    Show answer

    Correct answer

    • A

      The advertised prefix of 10.20.30.0/24 was configured using the network command.

    • D

      The output shows all prefixes advertised by all neighbors as well as the local router.

    Explanation

    For Option A:In Fortinet BGP (and standard BGP), when a prefix is displayed with an "i" (lowercase i) in the Path column, it represents an internal prefix that originated from the local router, typically configured via the BGP "network" command. In the exhibit, the prefix 10.20.30.0/24 is listed with a Path value of i, indicating it was injected into BGP by the local router using the network statement, not via redistribution from another routing protocol. The same logic applies to i as documented: "Origin code 'i' means the route was injected via the network command."

    For Option D:The get router info bgp network output is a summary table displaying both local and received BGP routes. It lists all known routes to the BGP process, whether received from peers or originated locally. The exhibit shows all BGP prefixes known to the local router, matching the official admin guide’s description of this command’s output.

    Explanation for B and C:

    The phrase “legacy route advertisement” is not formalized in BGP documentation or Fortinet’s admin guide; the output uses standard BGP mechanics.

    If a route was redistributed into BGP from another routing protocol, the Path field would display a "?" (question mark) for incomplete (redistributed) origin. Here the /24 route has "i" so it is NOT a redistribution.

    FortiOS Administration Guide: BGP Configuration and Route Table Interpretation

    Official BGP Command Show BGP Network, Path Codes, Route Origination Indicators

  11. Question 10

    Multiple answer

    In which two slates is a given session categorized as ephemeral? (Choose two.)

    Choose 2 answers
    Show answer

    Correct answer

    • A

      A UDP session with only one packet received

    • C

      A TCP session waiting for the SYN ACK

    Explanation

    The study guide states:

    “FortiGate categorizes an entry in the session table as an ephemeral session when it is a TCP session that is not fully established (three-way handshake not completed), or when it is a UDP session with only one packet received.”

    This directly proves:

    A is correct because a UDP session with only one packet received is ephemeral.

    C is correct because a TCP session waiting for the SYN/ACK is not fully established, so it is ephemeral. The study guide’s TCP state table shows that the handshake is only completed when the session reaches ESTABLISHED

    Why the other options are wrong:

    B is wrong because once UDP traffic has been seen in both directions, it is no longer the “single packet received” condition described for ephemeral sessions. The study guide says for UDP: 00 = one way, 01 = both ways

    D is wrong because a TCP session waiting for FIN/ACK is already in the closing stage after establishment, not in the “not fully established” stage. The study guide explains that after both sides close the session, FortiGate can keep it briefly in the table in state value 5 for out-of-order packets after FIN/ACK

  12. Question 11 Locked Unlock to see this question
  13. Question 12 Locked Unlock to see this question

167 questions locked

Unlock all 177 NSE7_FSN_AR-7.6 questions

You’ve had 10 for free. The other 167 work just like them: pick an answer, then check it.

Questions
177, each with its answer
Explanations
85% of questions explained
Formats
Multiple answer, Single answer
Version
8.2
Access
3 months from purchase

One-time payment

$49.00

Secure checkout