Launch offer: $20 off your order with code

NSE5_SDW_AD-7.6 Practice questions

Fortinet NSE 5 - SD-WAN 7.6 Core Administrator

0/5 checked

free questions
5
with answers
in the full set
141
question types
2

Updated

  1. Question 1

    Single answer

    A branch requires local internet access through two ISP circuits. It has no requirement to reach another site or send internet traffic through a hub.

    Branch LAN -- FortiGate -- wan1 -- ISP-A -- Internet

    \-- wan2 -- ISP-B -- Internet

    Which description of this SD-WAN design is correct?

    Choose one answer
    Show answer

    Correct answer

    • B

      The ISP circuits are underlays, and a site-to-site VPN overlay is not required for this local internet requirement.

    Explanation

    The two ISP circuits provide the transport connectivity, so they belong to the underlay. A VPN overlay provides logical connectivity across sites when such connectivity is required. This branch only needs direct internet access (DIA), so configuring two SD-WAN members does not itself require a site-to-site VPN or a hub.

  2. Question 2

    Multiple answer

    An administrator has selected passive mode for an SD-WAN performance SLA. Real TCP application traffic is available, but the matching firewall policy has not yet been prepared for passive WAN health measurement.

    Which two policy settings are required to collect passive measurements for that traffic in FortiOS 7.6.3? (Choose two)

    Choose 2 answers
    Show answer

    Correct answer

    • A

      Enable passive-wan-health-measurement on the policy that accepts the traffic.

    • C

      Set the policy outgoing interface to the appropriate SD-WAN zone.

    Explanation

    Passive health measurement analyzes real TCP session information. The accepting firewall policy must enable passive-wan-health-measurement, and its outgoing interface must be an SD-WAN zone.

  3. Question 3

    Single answer

    A Lowest Cost (SLA) rule matches a new session. Load balancing is disabled, minimum-sla-meet-members is 1, and priority-members is 3 2 1. All three members are alive and have usable routes. The rule uses one SLA target, and all other rule and zone settings use their defaults.

    Which interface should the rule select?

    Exhibit
    Choose one answer
    Show answer

    Correct answer

    • D

      wan3

    Explanation

    Members 2 and 3 both meet the SLA target, satisfying the minimum count of one qualifying member. Their costs are equal, and load balancing is disabled. The tie is resolved by priority-members, which places member 3 first, so the selected interface is wan3.

  4. Getting the hang of it? 136 more NSE5_SDW_AD-7.6 questions to go, each with its answer. Unlock them all

  5. Question 4

    Multiple answer

    A Lowest Cost (SLA) rule uses load-balance enable and hash-mode source-ip-based. All listed members are configured in the rule and have usable routes.

    There are no additional eligibility restrictions.

    Which two statements describe this rule while these conditions remain unchanged? (Choose two)

    Exhibit
    Choose 2 answers
    Show answer

    Correct answer

    • A

      wan1 and wan2 are in the eligible load-balancing pool despite their different costs.

    • D

      The source-ip-based method keeps traffic from a given source IP on the same selected interface under the stated unchanged conditions.

    Explanation

    With load balancing enabled inside an SLA rule, all usable configured members that meet the target can participate. Both wan1 and wan2 therefore belong to the eligible pool despite their different costs. The source-ip-based hash method sends traffic from a given source IP through the same selected interface while the stated candidate conditions remain unchanged.

  6. Question 5

    Multiple answer

    An administrator is troubleshooting ordinary IPv4 policy-based routes on FortiOS 7.6.3. The packet matches the policy-route address, protocol and port criteria.

    Which three statements about completing the forwarding decision are correct? (Choose three)

    Choose 3 answers
    Show answer

    Correct answer

    • A

      If only an outgoing interface is configured, FortiGate looks for a gateway using the routing table filtered by that interface.

    • C

      If only a gateway is configured, FortiGate looks for an outgoing interface using the routing table filtered by that gateway.

    • D

      If the required forwarding information cannot be resolved, FortiGate can continue to the next policy route.

    Explanation

    A policy route must provide enough information to forward the packet. An interface-only rule needs gateway resolution filtered by that interface, and a gateway-only rule needs interface resolution filtered by that gateway. If the required forwarding information cannot be found, that policy route does not match and FortiGate continues evaluating the list; ordinary routing is used if no policy route matches.

  7. Question 6 Locked Unlock to see this question
  8. Question 7 Locked Unlock to see this question

136 questions locked

Unlock all 141 NSE5_SDW_AD-7.6 questions

You’ve had 5 for free. The other 136 work just like them: pick an answer, then check it.

Questions
141, each with its answer
Explanations
100% of questions explained
Formats
Single answer, Multiple answer
Version
6.0
Access
3 months from purchase

One-time payment

$49.00

Secure checkout